The gist of my question:
- What is a "fiber optic" switch called?
- I.E. a layer 2 ethernet switch that uses fiber TX and RX connections and sends layer 2 network traffic between the fiber strands that are connected.
- Can someone purchase a dedicated fiber switch that does not have copper ethernet ports?
- What is the current average price of a device like this?
- Not necessarily looking for product endorsements, just information
- Might not make sense to go this route if it is too cost prohibitive
- What type of fiber connector is used for terminating a fiber strand into a jack on the wall?
- Can fiber be "patched" using two jacks and a "patch" cable?
- Is signal loss a concern with the longest runs at 100-200ft, a patch cable and media converters?
The full story:
My parents had unterminated fiber optic cable and terminated Cat5e run throughout their home when it was built in 2004. 10 years later the Cat5e isn't providing the throughput that my father needs to accomplish multiple streams of HD and fast system backups throughout the house. He can't reach gigabit speeds across the distance of the Cat5e runs.
We are both interested in terminating the fiber connections and using them as high speed "backbones" to copper switches in each room of the house. It would be easy to attain gigabit speeds (or better, eventually) using the fiber.
I have searched and searched for a "fiber optic switch" or "fiber optic router" and cannot find the correct term to describe this piece of hardware. We can use fiber media converters at the end points of each connection, however it would be nice to have a "patch panel" set up in the network closet in the basement that has fiber connections on it and switches the ethernet streams between the connections/systems in the house.
Each fiber media converter costs between $50-$100 a piece… After 10 or so terminated connections it might make sense to find a piece of hardware that does not require media converters. That would depend upon the cost of this hardware
Somewhat unrelated, if we are able to route between these fiber strands successfully, what is the physical connector type used in a jack on the wall? Just like RJ45 has a wall outlet (depicted below):
What is the fiber optic equivalent of this? In the interim could we "patch" a couple fiber strands together in the network closet? Would signal loss be of concern with a run length of 100-200 feet, a patch cable and two media converters? If that would work then it could be used until the funds are available for more.
Best Answer
What you are looking for is NOT a fiber channel switch. You are looking for an ethernet switch with SFP slots, unless you want an antique (GPIB slot). While you can purchase SFP switches with no copper slots, it's often not the best or most affordable solution. Then you need SFPs (Small Form Pluggables) which are the devices that actually connect to LC fiber optic connectors and plug into the slots.
On the low end you can get Gigabit 8 copper 2/SFP ethernet switches for $100 each, or less. Be careful not to buy 100Mbit when shopping used stuff. Much larger than life, an SFP:
An SFP switch (this exact one possibly no longer available new, but there are many, and used works fine in most cases anyway) with 16 copper and 4 SFP (fiber) slots
With no connectors in place, if going there, use LCs - everything "modern" does. But you'll find the process is rather expensive to set up for doing, or to have done.
You also need to figure out what your fiber is (singlemode/multimode - & what core size (50 or 62.5) if multimode, and whether it's OM3 or 4 if it's 50), so you can buy the right SFPs, and you'll want to carefully look on ebay to see if you can find some at a reasonable price. It's not a small undertaking (I got a baptism by needing to do a large project with virtually no budget 3-1/2 years ago.)
If your house is not huge, there may be a simple wiring issue with not getting full throughput on Cat5e - it should be good for gigabit up to 100 meters - 328 feet. That would be lot cheaper to solve than terminating a bunch of fiber, unless you have the tools already, which seems unlikely. Often electricians who are not network techs mess up Cat5e installs, IME. Phone techs are (or were circa 2004) prone to use Cat3 or Cat5 jacks since many of them did not stock Cat5e jacks and few customers were actually using gigabit then to notice - that might be the first thing to check. Better switches can also be set up to trunk several copper connections (if several connections are available between places you want to go) to provide 2, 3, or up to 8 GB over copper.
To clarify a bit with more space than is in comments - fusion spliced no-polish (prepolished) conectors are OK, but expensive (both to buy and to have the equipment to use, though you can rent a splicer.) A fusion splice is, in most cases with a modern splicer, a good splice. The field-termination mechanical splice connectors are great in the eyes of the salesmen, and nobody else...a mechanical splice has several issues right from the get-go, and despite the protestations of the salesmen, real users find that the index-matching gel used to make them somewhat better than they would be without it dries out, turns brown, or both over time, making the connector lose light transmission ability. Epoxy polish (where the actual fiber is inserted in the connector and held with epoxy, then polished in the connector) is as good as you can get if you actually need a connector, assuming you do a decent polish job (not all that hard if you follow the correct procedures with the correct abrasives.) If you don't need a connector you can disconnect, a fusion splice is better.