—BOUNTY & EDIT—
Ok, here is the latest update, and attached a bounty! So I ran all of my ram sticks 1 at a time for around 24 hours each. None of them caused a BSOD. I ran test on all of the ram while I was running each. So I went to put '2' in at a time (dimm 1/2). I tried to put them both in the same dual-channel. The computer would not boot up. I moved them to the other dual-channel (dimm 3/4) and they would not boot up. I put one in Dimm 4 and Dimm 2. The computer booted up. So I played around for a little bit, shut the PC down and tried dimm 3/4 again. The Computer would not boot up. I tried Dimm 4/1 and the computer would not boot up. The only way it seems to let me boot up with more than one ram stick is to use DIMM 2/4. Is this odd? When I opened the case the first time, they were using 2/3/4 and not dimm 1. Is this normal of HP? I'm not sure that I have a problem trying to boot up with dimm 1 and 1 ram stick, I will try that later. During the single ram stick test(s), I was using DIMM 2.
I made a post on here a week or so ago, but my pc's condition is getting far worse. I've done a lot more research and have more to offer. I upgraded to windows 8, but I had the same problem on Windows 7.
Here's my system specs: My HP PC
I want to mainly point out that it is a 250w power supply. I got it from my brother who said that it had been crashing randomly. It's a year or two old.
Ok, so the crashes are random, and can be while I'm doing hefty stuff, or basically sitting idle. When it crashes, sometimes I get to see a BSOD (which saves and sometimes doesn't get to) and my screen tends to have colored lines on it. Sometimes the PC will restart fine, and sometimes I have to wait for 10 minutes unplugged before I can start it back up.
Now when I say it wont' turn back on.. I mean: Power button shows on, fans spin, green light on back and on motherboard are on, but screen says 'no signal'
I have done every test known to man on the HDD, and everything checks out. It has 6 gigs of ram (3×2) and I am all individually, trying to get the crashes. My CPU doesn't rut hot at any point, and theres times where the PC will set for a day, I boot up and it crashes in 10 minutes. The PSU does get warm, and blows out warm air. My case is cool and side is open.
Everything is integrated, there are no add-on cards, add-on GPU's,. The only thing I would consider to be an addon is the front Media Card slots, which I rarely use.
The only thing plugged in – HDD, CPU Fan, Back Fan, Keyboard/Mouse, Ethernet Cable, and speaker input.
95% of my bsod errors are due to ntoskrnl.exe , and I did get one classpnp.sys error.
The bsods are displayed as "irql_not_less_or_equal" "internal_power_error" I've seen others, but can't remember them off the top of my head. But they were still caused by ntoskrnl.exe.
A lot of things point to driver(s), but how can my drivers effect my PC from not turning back on for 10 minutes (sometimes more)?
Last note: The only time I've ever heard my PC beep is when I took ALL of the ram out. Other than that, I've never heard a beep code.
–Edit–
I am down to running 1 ram stick again, which it hasn't crashed in over 12 hours. Even if the ram was good, I usually run it at 6, and at 4.. it has been crashing more so when running higher amounts of ram. It has crashed with 1 stick in there, but not as often.
–Edit–
Ran the 1 ram stick for 24 hours without a single glitch. So I'm switching to another ram, and putting a dot on the tag of the 1st ram stick. I'm really trying to narrow down the problem.
Best Answer
See this link on a quick tutorial on how to debug BSOD. Check your C:\windows\minidump folder for .dmp files and load them into the debugger (once installed).
This will save you TONS of time and headache trying to guess at what is causing the BSOD. Often, it's a display driver that's doing it.
http://www.dell.com/support/troubleshooting/us/en/19/KCS/KcsArticles/ArticleView?docid=543301
Let me know if you have any issues.
Ensure you motherboard has the latest BIOS installed as well.