Using USB-C Apple Adapter to Charge MacBook 12′ with USB-A Port – Compatibility Guide

Can a Macbook charge it's batteries from a USB-A charger (car or wall) or battery pack?

It depends, but yes, it should work. The charging performance may vary from it charges very slowly to not at all.

"Type A" is the connector type; it has nothing to do with how much power is being delivered. What you need is a power adapter that is compliant to USB 3.1 specifications. It just so happens that to connect it to your MacBook, you need a "Type C" connector.

Would I recommend you doing this? Absolutely not.

Important Note: Plugging into a power source that is significantly lower than what is required by your device can and will damage your equipment.

---

Why?

First, we need to know what the power requirements are to power the Macbook; per Apple, it requires a 29W USB-C Power Adapter (see below).

Generally speaking, the USB Type A adapters most people are familiar with are those that charge their iDevices. These are based on USB 2.0 at best and according to the specifications, they are limited to 5V 1.5A.

That means, those chargers are limited to 7.5W.

(Watts = Volts * Amps)

7.5W is nowhere enough to power your Macbook.

If you notice in the above USB 3.0 pin out diagram, there is only 1 5V (VCC) pin (this is important in understanding USB 3.1 further down).

The USB 3.1 is the specification that says it will support up to 20V at 5A. Using the same equation from above we get a specification that is capable of handling up to 100W so there's enough power "bandwidth" to charge your Macbook. But that's using a special communications protocol over a USB-C cable.

20V * 5A = 100W

However, the basic spec is still the same, 5V but now at 3A and there are two 5 volt pins as opposed to only one for USB 3.0 and earlier. This means combined you can get 10V.

If you notice in this pin out diagram there are two 5V pins (Vbus). These are combined to make 10V.

Note: There are some USB 3.1 Type A adapters out in the wild, but they are so few and far between I wasn't able to find a schematic for the pinouts. I am using Type C since these are the most common.

So using our trusty equation again,

(2x 5V) * 3A = 10V * 3A = 30W 

30W is within spec of charging your Macbook.

But what about the cable? Plugging in a USB 3.1 (A to C) into a non-USB 3.1 power adapter will not fix the problem. The adapter is only providing 5 volts on one pin, not on two that's required to get the appropriate amount of current.

I would go for USB-C to DisplayPort directly. That would be one relatively inexpensive ($20 to $40 US prices) cable to do the job. Since your display won't charge the MacBook and do video over a single USB-C cable and you have several ports (display side and Mac side) - a dedicated cable would be my choice.

I like the USB-C to HDMI adapter you mentioned for my MacBook since there is only one port and charging plus USB is needed, but on the MacBook Pro you have several ports and can use one per display without too much hassle. It will work for you, though - just not my first choice.

Apple even recommends against using the adapter you mention for bridging between a Mini DisplayPort device and thunderbolt 3. - https://support.apple.com/en-us/HT204154

Note that although it uses a Mini DisplayPort connector, the Thunderbolt 3 (USB-C) to Thunderbolt 2 Adapter doesn't support connections to Mini DisplayPort displays.

If you only want two external displays, both 13 inch models of MacBook Pro are suitable. You'll need the 15 inch models to support 4 displays. That might be a non-issue if you only have one Dell display to connect.